Canadian Sweptline Addict

[jgeebee63]

Here is a shot of my 1967 Dodge D-100 that I am working on to drive to the Sweptline cruise in September. It will soon be home to a hot rodded slant six with a 904 automatic behind it. It is in the garage now, so that is progress

67 shorty.jpg (8.96 KiB) Viewed 3089 times

Here is my 1971 Dodge Custom D-100 long bed. It has a 318 small block with a 727. It soon will be getting a dual plane manifold and Holley carb, headers and RV cam.

my 71-2.jpg (7.5 KiB) Viewed 3089 times

If anyone has any body trim for the 71, I would be interested in finding the pieces I am missing.

Thanks,

Jason

[68slant]

i have complete set but the drivers side fender.

[jgeebee63]

How much do you want for that stuff?

[wally426ci]

Cool trucks!!

[Hobcobble]

Welcome to the site.
John

[MountainMoparRobin]

I didn't see this thread before, glad to see you get the pictures up See the 67 in September

[68Dodge1]

nice trucks,look forward to meeting you at the cruise

[runcharger]

PM me what trim pieces you need. I may be able to help and I live in B.C. which makes shipping a bunch easier.

Sheldon

[MountainMoparRobin]

Gettin closer to the time to check out the "Pissed off hive of Bees"! I've got an Slant 6 sittin, you just may inspire me to do something wild with it

[jgeebee63]

I got the engine and trans pulled from the 67 today. I have a bit of clean up of the frame and firewall to do while the engine is out and then it starts going back together. A wire wheel and a rattle can of paint will have to do.

[jgeebee63]

I got the frame and firewall cleaned and painted. The slant six is installed. Tomorrow's task is getting the 904 auto trans installed and a crossmember built. I will take some pictures. It is probably a good time to start a build thread, I guess.

[MountainMoparRobin]

just in time

[jgeebee63]

The exterior of the cab, box and hood are now painted flat black on the 67. It is starting to look pretty cool!

[ArtfulDodger]

Hi Jason;
You said you were going to put a four barrel on your 71.
If you don't already have an intake, I have a 340ci cast factory manifold dated 1972.
I was going to put it on my 71, but decided against it.
I am in Whitby/Oshawa area. Have been to Sterling market many times.

[jgeebee63]

Hi there,

I live in a little village called Stirling, Alberta. Sterling, Ontario would make getting a hold of your intake a lot easier. Dang it!

[ArtfulDodger]

Whupps!
Alberta eh?
Guess I wasn't thinking outside my little world of Ontario.
I like the colour of your 71. Mine is orange with the factory wrinkle paint roof. 318 auto with factory power steering.
Guess i better let you get back to putting the tranny on the back of the engine for the earlier one.

[jgeebee63]

I finally took some pictures of the 67 and posted them on Facebook.
I tried to get back on the computer to start a build blog, but it is broken. I'm down to surfing the web on my PS3 until I'm can get it fixed. The 67 is starting to look pretty cool.
I´ve been painting the fenders and underside of the hood. Swepty's look really cool in flat black!

[MountainMoparRobin]

I finally took some pictures of the 67 and posted them on Facebook.
I tried to get back on the computer to start a build blog, but it is broken. I'm down to surfing the web on my PS3 until I'm can get it fixed. The 67 is starting to look pretty cool.
I´ve been painting the fenders and underside of the hood. Swepty's look really cool in flat black!

Flat Black or Satin Black? I'll have to go check it out

[jgeebee63]

Rustoleum flat black. What is the difference between satin and flat?

[MountainMoparRobin]

They are probably the same, I used Satin Black on my 65 to make it eye exceptable before the Cruise.