hey everybody
heres my stupid question for the week! ill be building out my poly engine and im not really a fan of the 3 on the tree. im really wanting a floor shift 4 speed. what tranny should i be looking for to handle 400ish hp? thanks for any suggestions!
4 speed manual
-
flyngreenmole
- Sweptline.ORG Member
- Posts: 75
- Joined: Sun Dec 05, 2021 9:43 pm
- City: Sandy
- State: OR
4 speed manual
your only crazy until your not!
Re: 4 speed manual
Not a big fan of the column shift in the relatively tight cab of my '65, so I understand.
The A833 4 speed should definitely handle that level of power. There was even an overdrive version used in the trucks.
The A833 4 speed should definitely handle that level of power. There was even an overdrive version used in the trucks.
-
flyngreenmole
- Sweptline.ORG Member
- Posts: 75
- Joined: Sun Dec 05, 2021 9:43 pm
- City: Sandy
- State: OR
Re: 4 speed manual
thanks baker! ill start looking around. i like the idea of an overdrive...
your only crazy until your not!
-
Txas2step
- Sweptline.ORG Pioneer
- Posts: 3417
- Joined: Mon May 31, 2010 7:26 am
- City: houston
- State: TX
Re: 4 speed manual
The A833 4 speed will not work with your Hydro. set up. The 10 spline NP435 would be a direct fit. Do you have the e brake on your existing A745 3 speed?
61 shorty 170/ 3spd 3:91(sold)
66 lwb 318 poly/727/4:10 (sold)
67 shorty 318poly/4spd 3:55
68 ute 318/3 spd/3:55(sold)
70 318/727/3:23
66 d200 225/4spd/4:10( military)(sold)
68 d100 383/727/3:55
66 lwb 318 poly/727/4:10 (sold)
67 shorty 318poly/4spd 3:55
68 ute 318/3 spd/3:55(sold)
70 318/727/3:23
66 d200 225/4spd/4:10( military)(sold)
68 d100 383/727/3:55
-
dodgeboykim
- Sweptline.ORG Pioneer
- Posts: 3064
- Joined: Wed Dec 31, 1969 6:00 pm
- City: Chilliwack. B.C. Canada
- State: Foreign
- Location: chilliwack.
Re: 4 speed manual
You can put in an A833 OD trans but will need all the accompanying mechanical bell housing parts, Flywheel etc to install trans into a 68 and earlier. Manufacture a bracket to use Hydraulic slave and a trans crossmember.
Existing crossmember for hydraulic bellhousing mounts may have to be cut out for clearance.
Existing crossmember for hydraulic bellhousing mounts may have to be cut out for clearance.
My truck is younger than me.
66 W100. 70 D 500 , 69 Hiab Speed Loader. 96 Ram 3500 Club Cab Cummin's 5 spd. 97 Ram 1500 Club Cab 5.9 gas auto. 83 W200 LB Propane 360 auto 09 Yammy Rhino 700.
66 W100. 70 D 500 , 69 Hiab Speed Loader. 96 Ram 3500 Club Cab Cummin's 5 spd. 97 Ram 1500 Club Cab 5.9 gas auto. 83 W200 LB Propane 360 auto 09 Yammy Rhino 700.
Re: 4 speed manual
Brewer's is a great source for anything A833. Very helpful.
As the others have mentioned, it's not easy, but it is doable.
As the others have mentioned, it's not easy, but it is doable.