Sweptline.ORG

So today at the junkyard I found exactly one 71 power wagon. According to the tag on the doorframe it has 3.23 gears. It was a 383/727 truck but the 383 is long gone. Trans and Tcase were untouched. I have never heard of a sweptline with 3.23 Dana 60. My D200 currently has 4.10 Dana 60 and the chang...

Looks cool. Wonder if there is any more info around the ol internet about it?

http://justacarguy.blogspot.com/2015/10 ... aster.html

Casting number is 1852029-1 build date of 63, numbers on top of pad are 42 and 6 and "WT" and Aaqa 4R on the front of the block. it came out of an irrigation pump in Nebraska, had a two barrel, funky heads different than any other RB I've seen (angled spark plugs and different shaped exhaust ports. ...

so are they actually building asn selling these kits now? I couldnt find anything on thier website. What is the price?

Anyone know where I can find the right pitman arm? The shims are already out as I had them removed along with a couple of leaves a while back to lower the front of the truck.

So all I need is this?

http://www.ebay.com/itm/Steering-Drag-L ... 07&vxp=mtr

Since owning my D200, I have dealt with the factory crappy power steering that leaks like crazy and has some play in it as well. The leaks caused me to have to remove the belt and basically I've been driving it around with no power steering for a while. I also put on some skinny 235/85/16s and it is...

With the size of your trailer and four speed, so you'll have that granny low first gear grunt to get it moving, what kind of hills and mountains will it see? I'd say leave it as is and give it a shot and if it isn't enough, go with a 383 2 barrel swap, won't cost a lot and will make lots of torque a...

As for the rear bumper they were aftermarket for years. I found one that looks exactly like the one in the picture on an 80s Ford in a junkyard, it was within a 1/4 of an inch (1/8 per side) of being the perfect width for the brackets to fit. So basically a couple of washers and drill some new holes...

My 383 made it 44 years and 96k miles before the oil pump went out, it still runs, but makes some hellacious noises in the bottom end and zero oil pressure. I have an old 63 426 Wedge I would like to build to replace it. I am thinking of something around 500HP.... edlebrock heads, aftermarket cam, p...

Advance auto parts mirrors... Cheapos

Passenger side

So I found some mirror. Brackets, from a 61- 68 international pickup truck. The curvature of the bracket matches perfectly with the sweptline door... I had to wallow out the mounting holes just a bit on the bracket, and they bolted right onto the west coast mirror bracket holes 2 out of 3 bolts. Thi...

Tony292 Horseshoe bend idaho

I would go with overload springs in the rear at a minimum, the camper specials had them. how many leaves in the rear does your truck currently have?

Here is a pic

So I bought the engine, it came out of an irrigation setup and has the funky heads but water pump isn't high, it's in the same place as any car or light truck water pump. The oil pan is different thought. So a set of used heads and oil pan and I'll be set, probably have a look at thei pistons while ...

Anyone know where to get the rubber gasket for a side wing vent window for a 71? My drivers side is mostly gone and going to the car wash results I a wet floor and drivers seat....

pull out a leaf or two on each corner, I did only on the front and dropped the front 3 inches.


Before:




After:

http://grandisland.craigslist.org/pts/4683307144.html

water pump looks like a standard BB water pump, heads were very different with angled spark plugs and different bolt pattern for exhuast manifolds. could not tell much more about it as it is all together.