Sweptline.ORG

John is on the money, I sold a white wheel w/ ring and button last month for $100 . It had a crack where one of the the spokes met the center BigG

Make sure you measure the c/l to c/l on your cross member , I found out the hard way one set of centerlines on the mount is wider than the other , they both fit the 727 but not the crossmember. By the way that is the right mount. (the flat one) BigG

I prefer the gasser look10" steelies on back5- 6" Americans on the front, and headers w/ elec. cutouts Thanks for the help. BigG

So, if I want to raise the front end of my sb 66 2" I will need to make longer shackles and add some length to the pitman arm ? Thanks, BigG gkannenberg@jps.net 209-712-1186

So, if I decide to raise my sb 66 about 2 " what would I need to do besides build new shackles,and add more length to the pitman arm ? BigG

I went into www.aaroncake.net/rx-7/efaninstall.htm and it was very helpful. I have a large used fan ( came w/ all the stuff) installed to push from the front. The instructions say it is critical that the fuse is located as close to your +12v source as possible, what it does not say is the probe shou...

I have pictures of this from a door I cut open, fairly simple, just make sure you get ALL the stuff. Lock cylinder lhas a slide clip, asst. screws, etc. Lock cyls. can be rekeyed to the same key if they match. If you don't find the parts , call me at 209-712-1186, I may have them, or also email pict...

I have installed a 1979 440 M/H motor in my 66. After MUCH confusion I decided to use the original steel mounts and turn the new rubber mounts upside down. This left the single stud facing down. Then after careful measuring and making sure I had the motor where I wanted it ,I marked and drilled a ne...

I have a spare tire support off a 1967 Dodge long bed and a spare tire mount for the front bumper for the same. I live in Galt, please reply if interested. Thanks BigG

Here are two pictures of brackets, you will have to figure out the spacing which is pretty simple. BigG

My truck is a 66 with a 1970 front axle BigG

Just changed the studs on the rear to right hand thread, now I am looking for two right drums/ hubs for the front. Can anyone help? BigG

I replaced the motor mounts on my 1966 d100 w/ 1979 440 engine yesterday. After trying several different opitions , I ended up loosening the two bolts on the automatic trans and all the bolts on the rubber and steel (on the engine) mounts. I then used 2 wooden 2x4s about 12" long and two bottle jack...

Thanks, BigG

Does anyone know if a D100/1501966 front axel interchange with a 1970d100/150 front axel? My Hollander has different #s for these. They look the same but is the width and mounting the same? ? Will the 70 bolt right up to a 66? BigG

I have used these guys in Elk Grove , Ca , for my 66 Dodge pickup locks, they are GREAT ! BigG

My headers are Hedman # 79220, they are the only ones that would clear my old crossmember which is part of the front spring supports. They dump out under the supports. ( My 66 crossmember is cut off next to the spring supports to make room for the 727) I added a basic flat 1968 crossmember to bolt u...

I AM BUILDING A 66 SB W/440/727 AND HEADERS , WILL TRY AND GET THE #'S OFF MY HEADERS TOMORROW. BIGG

I am in the process of building an old slant six 1966 d100 . I have pictures of 440 installed, cross member cut off, later crossmember installed, correct headers ,radiator, etc. If this would help I will post info and pictures for everyone to see and use. Big G

A big thanks for the tach wiring diagram, it answers a whole lot of questions. Big G