Sweptline.ORG

I'm interested in knowing what the GVW is for a 1970 W100 long bed?
THanks

Chris, I'm wishing I had a Sweptline again! Will someday. I look all the time. congrats on the new ride!
Keep the positive attitude and keep on trucking.
Jay

Glad this truck went to someone who truly needs it!
It should get you in and out of your place come bad weather.
I wish the next truck is as good as this one.
All the best, Jay

Is it possible to powdwecoat over existing powdercoating? O does the piece need to be sandblasted then prime and powdercoat?

The weather held off untill late night!
Lots of Mopars!
This being the first month.. lots of great rides!
My son had the Charger all shined up and looking great!

Pay Pal sent!
This site is the best for keeping our trucks on the road!
Everyone needs to stepup and donate.

Didn't drive the truch, but did drive the Charger up to Louisville on Christmasday for dinner at my daughters home.
Got to see the grandsons open gifts. As they say Christmas is for the kids, what fun!

Sign me up! Not sure what to bring, just depends on the weather. But we'll be there.

It"s marked down and reday to go. Just don't know which one I'M driving yet, Charger or Powerwagon. Weather will deside.

Robin, I used PPG on the inside of the truck with good results. Didn't check prices VS SW.
Once you finish painting you could give us amateurs some lessons!

Proper grounding is key to having your lights work correctly. They have some paint and yearsof dust and dirt on them, so take the light buckets out and use wire brush to clean behind the screws and on the frame so the contact is better.

I used the ones fron auto bodyspecialities and had to some adjusting with a BFH and some cutting. But they went in ok. Just make sure you leave enough of the old floor to weld to. Part of mine was so thin I had to use epoxy on some seams.

What a great time! Everyone I spoke to enjoyed the event. Great food .... great people.... great trucks. BUT why wait until next year to get together again. Robin big thanks for putting it together.

Sometimes it helps to put the stripper on and while it is still wet putheavy plastic over the top of the stripper! This helps the stripper penerate thru the severallayers of paint and primer! I have done this befor and it really helps. Aircraft stripper has worked well for me in the past.

Checked the drive shaft and it spun freely! Thanks for thegreat advise, had myconcerned for awhile. Drove the truck yesterday about 100 miles and this truck is GREAT! Just need to do something about the steering!!! :thinking I had to chase the truck all over the highway. How dificult is it to adjust...

Work on the 70 Powerwagon is progressing nicely! Took it out around the block the other day and the front drive shaft was spinning?? Hubs were in the free position with the transfer case in 2 high. Is this normal or is the transfer case engaged in another gear than 2 high? Did shift it thru several ...

All sounds like good advice. I also think disconnecting the braks lines and putting some air thru the lines, checking to see if there is a blockage or dirt in the lines. Have to try everything. Drilling the holes in the master? After spending $85.00 I'd hate to screw up the part and have to get anot...

This problem isn't on my Sweptline.... However it is a Dodge product. I have replaced everything on each wheel. Everything new shoes, springs, wheel cylinders, master cylinder with new, not rebuilt, even the vacume booster! The problem is after a short drive of maybe 3-5 miles the brakes are fully a...

You might try to find a box that has agood back section and plasma cut off the back part. I was going to do this on a '70 got the part but sold the truck befor I got it welded into place. Now I have the rear section sitting out back. Yours if you want for $200 plus shiping.

It works! Pulled themaster cykinder one more time. Benck bled it again and adjusted the push rod from master to vacume booster and everything works now! :dance Now just have to adjust the shoes a bit. After a year of messing around the go fast mobile has stoping power! Now my next question who can d...