Sweptline.ORG

64D100Poly

Hello, I figured that in ain't a bad idea to replace the original tie rod ends on my early 65 d100, seems they only make the right hand thread ones. I know that this topic has been posted multiple times but I wanted to make this post just in case anybody started producing them as of recent. I've fou...

64D100Poly

My centerlink was bent pretty bad to the point that it would bind on the front axle when you would hit the brakes! Somebody in the past managed to reverse over something and hit it so hard it bent the link and axle pretty bad, had to get it glowing with oxy fuel and pound it back, thank you for the ...

64D100Poly

My early 65 d100 has it

64D100Poly

hmaynord wrote: ↑
Fri Feb 11, 2022 12:42 pm
where from?

I got em off Ebay never used in the original box for $15 on a bid with one other person, they had been listed weirdly so I guess not many people found em.

64D100Poly

I replaced every electrolytic capacitor in mine, I also soldered in an aux cord into the volume pot so I plug my phone in and it throws the phones audio signal in before the AM radio signal, unplug it and its just like factory. Great idea! What kind of phone, where did you get a speaker output from...

64D100Poly

Probably somewhere between $15-$30 depending on condition? :thinking This has 48+ year old capacitors, resistors, etc. in it.... so there's no telling when it'll give up the ghost. :thinking :lol: John I replaced every electrolytic capacitor in mine, I also soldered in an aux cord into the volume p...

64D100Poly

I just found a original pair of 12" Anco red dots for my '64 to replace the cheap aftermarket ones the previous owner had installed, according to the parts manual it uses Turtleback 800's which is what I got. I don't know if this helps for refills but it should take a 12" curved windshield Anco Turt...

64D100Poly

Mark DuVerger was the author of the video. I offered some suggestions to improve the rebuild, as comments to the YouTube video. Mark disagreed with most of them, especially the adding of a grease zerk to the hinge arm, to allow for lubrication. He claimed the bushings were "Oilrite" brand and did n...

64D100Poly

PwrWgnDrvr wrote: ↑
Mon Feb 07, 2022 1:15 pm
That ad is ridiculous. It shows a 1/2 or 3/4 ton in an ad for a 1 ton

I was confused when I saw it too!

64D100Poly

My truck has the original dealership decal for Bill Breck Dodge out of Colorado Springs on the tailgate, going through some old newspaper clippings I found online it shows an ad for a new decently standard 1-ton with a 50,000 mile/5 year bumper to bumper warranty listed at $1799. I wish new trucks w...

64D100Poly

675-5143 is the Napa part number. I tried to install them using the You-tube video with no success, pin would not come out. Heating and then using a press might be helpful. The end of the hinge is mortised with drill press before installing pin to accommodate the bushing which was countersunk accor...

64D100Poly

Amazing detailed write up, what is that box with a cable sitting just above the reservoir? Is it cruise control?

-LB

64D100Poly

Hello, I've decided to finally get to replacing the pins in my driver side hinge, I remember for a while there was a good video on YouTube of someone changing the pins in them, unfortunately the video has since been deleted. Does anybody have a part number for a hinge pin kit that is known to work o...

64D100Poly

The IMCDB site is pretty cool, you just select the car you want and it will show dozens of movies with the vehicles appearance!

https://www.imcdb.org/

64D100Poly

Did you measure both drums to figure out what’s rubbing? Take both back to Napa and have them measure and throw it on their brake lathe. Might just need the edge cut. :2cents :2cents Craig The drum has a channel around it that the backing plate runs in between. The edge of the backing plate sticks ...

64D100Poly

I got a 65’ D100 with the non-tapered axle. The shoes were wore out and dug the robots into the drum. I have looked everywhere and can’t find a new replacement drum. I got some at Napa that fit fine besides the rub against the backing plate.
Does anybody know of a rear drum that will fit??

64D100Poly

swptln wrote: ↑
Sat Jul 17, 2021 6:07 am

64D100Poly wrote: ↑
Tue Jul 13, 2021 7:14 pm

swptln wrote: ↑
Tue Jul 13, 2021 6:26 pm

Does your truck have the "Custom" badge/emblems on the doors?

Yes I have that emblem below the wing window

64D100Poly

Do you have a SERT tag on your door jamb? It could be a number of things. If there were any special ordered parts, they will be listed on a SERT tag, if they were standard option packages in the truck, there would be no reason for the SERT tag. Could be "Custom Cab" appearance package, etc. I only ...

64D100Poly

I got a 1965 Dodge d100 Sweptline I was going through and bleeding my brakes when I looked up at the frame and sandwiched between the frame and the cross member for the bed was the build sheet. Unfortunately, 50 years of wear and tear had it's way with it and little is legible, but I would have what...

Sweptline.ORG

Search found 119 matches

65' D100 Left Tie rod End Availability

Re: Need tie rod ends for 63 d100

Re: Fender Pentastar emblem placement

Re: Wiper Blade Refills

Re: Original Radio

Re: Original Radio

Re: Wiper Blade Refills

Re: 65 D100 Driver door hinge repair

Re: Original price?

Re: Original price?

Re: 65 D100 Driver door hinge repair

Re: Adding Wash, Wipe, Mist, Delayed Wipe to a Sweptline

65 D100 Driver door hinge repair

Re: Dodge Trucks in the movies and TVs

Re: Rear drum replacement part#

Rear drum replacement part#

Re: Found my Build Sheet, Got a couple Questions

Re: Found my Build Sheet, Got a couple Questions

Found my Build Sheet, Got a couple Questions