69 W200 Transfer Case Crossmember
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
69 W200 Transfer Case Crossmember
I'm chasing down some driveline vibration on my 69 crew cab. The T-case cross member is a retrofit from an unknown truck and I had to drill new holes since none aligned with frame. This crew was 4x2 until I converted to 4x4.
I think I'd like to replace the cross member with a known good un-bent unit as a starting point. Does anyone know where I could get a new or used crossmember. T-case is divorced NP205.
Thanks.
I think I'd like to replace the cross member with a known good un-bent unit as a starting point. Does anyone know where I could get a new or used crossmember. T-case is divorced NP205.
Thanks.
- powerwagon54
- Sweptline.ORG Pioneer
- Posts: 1335
- Joined: Wed Dec 31, 1969 6:00 pm
- City: Washougal
- State: WA
- Contact:
Re: 69 W200 Transfer Case Crossmember
I may have one in Washougal, I will get back to you.
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
Re: 69 W200 Transfer Case Crossmember
Thanks PowerWagon54. When do you think you'll have a chance to check? Many thanks.
- powerwagon54
- Sweptline.ORG Pioneer
- Posts: 1335
- Joined: Wed Dec 31, 1969 6:00 pm
- City: Washougal
- State: WA
- Contact:
Re: 69 W200 Transfer Case Crossmember
Sorry I just looked. I am out of them
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
Re: 69 W200 Transfer Case Crossmember
Thanks for checking.
I see on internet that some people make their own. Anyone have ideas on whether I should find used or try the McGyver route?
I see on internet that some people make their own. Anyone have ideas on whether I should find used or try the McGyver route?
- marklein
- Sweptline.ORG Member
- Posts: 607
- Joined: Sun Nov 11, 2012 9:55 am
- City: Red Deer
- State: Foreign
Re: 69 W200 Transfer Case Crossmember
I have one from a 69-71. Rest of the frame scrap, I salvaged all that was good. Not sure how much shipping would be though. Let me know if you are interested.
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
Re: 69 W200 Transfer Case Crossmember
Yes I'm interested. What part of the country are you in? I'll look around for shipping options and get back to you. I'm guessing 1'X1'X3.5' would be the box size. Could you provide pictures?
- dodgeboykim
- Sweptline.ORG Pioneer
- Posts: 3016
- Joined: Wed Dec 31, 1969 6:00 pm
- City: Chilliwack. B.C. Canada
- State: Foreign
- Location: chilliwack.
Re: 69 W200 Transfer Case Crossmember
BlueManCrew wrote:Yes I'm interested. What part of the country are you in? I'll look around for shipping options and get back to you. I'm guessing 1'X1'X3.5' would be the box size. Could you provide pictures?
Hes shipping from Red Deer, Alberta, Canada.
My truck is younger than me.
66 W100. 70 D 500 , 69 Hiab Speed Loader. 96 Ram 3500 Club Cab Cummin's 5 spd. 97 Ram 1500 Club Cab 5.9 gas auto. 83 W200 LB Propane 360 auto 09 Yammy Rhino 700.
66 W100. 70 D 500 , 69 Hiab Speed Loader. 96 Ram 3500 Club Cab Cummin's 5 spd. 97 Ram 1500 Club Cab 5.9 gas auto. 83 W200 LB Propane 360 auto 09 Yammy Rhino 700.
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
Re: 69 W200 Transfer Case Crossmember
Ok. I need psychotherapy.
Engine angle ( on my driveway) is +4.5 degrees downhill. My transfer case is +3.8. As measured by the bottom of the input vs. output shaft. My rear differential is -6 as measured from the top of the leaf spring riser (see photo). I don't know what a good reference angle is from the rear axle. Ideas?
Engine angle ( on my driveway) is +4.5 degrees downhill. My transfer case is +3.8. As measured by the bottom of the input vs. output shaft. My rear differential is -6 as measured from the top of the leaf spring riser (see photo). I don't know what a good reference angle is from the rear axle. Ideas?
Last edited by BlueManCrew on Wed Sep 28, 2016 9:58 am, edited 1 time in total.
-
- Sweptline.ORG Pioneer
- Posts: 4041
- Joined: Fri Feb 15, 2008 8:46 pm
- City: Wichita Falls
- State: TX
- Location: wichita falls,texas
Re: 69 W200 Transfer Case Crossmember
I need psychotherapy too, as I can't see the photo you referenced.
Are you saying the rear differential pinion is pointed down?
Bucky
![Laughing :lol:](./images/smilies/icon_lol.gif)
Are you saying the rear differential pinion is pointed down?
Bucky
1966 W500
1975 W600
1978 W200 club cab
1975 W600
1978 W200 club cab
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
Re: 69 W200 Transfer Case Crossmember
Ok. Photo added. The angle I refer to is that flat riser head just below the leaf spring. Another reference point is the rear pumpkin cover flange minus 90 degrees. That Dana rear axle doesn't seem to have any easy obvious reference point.
Thanks.
Thanks.
Re: 69 W200 Transfer Case Crossmember
You need to remove the cap straps and bolts(and driveshaft end of course) and get the angle off the front face of the yoke.
https://www.youtube.com/watch?v=DDmz0tibVGM A video about driveshaft set up.
https://www.youtube.com/watch?v=DDmz0tibVGM A video about driveshaft set up.
I sold all of my sweptline trucks,except the invisible one. I just couldn't stand to see it go!
( )
91w350 CTD
93w250 CTD
( )
91w350 CTD
93w250 CTD
-
- Sweptline.ORG Member
- Posts: 34
- Joined: Mon Sep 30, 2013 8:25 pm
- City: west richland
- State: WA
Re: 69 W200 Transfer Case Crossmember
Thanks. I took the drivelines off and took the following measurements at each pinion flange.
Front to back....on my driveway which is not totally flat. Front of truck higher than back, but its all relative.
* Back of engine/transmission = 5 degrees downhill
* transfer case = 3.5 degrees downhill
* Rear axle pinion = 1.5 degrees positive tilted up towards T-case.
* Did not measure front axle yet.
These are average numbers. I used cell phone and harbor freight digital meter. Quite a bit of variability so I averaged.
Adjusting the transfer case will be easy as there is play from holes being slightly larger than bolts. I'll leave the top front bolts tight then use a jack to allow it to swing to desired angle before tightening.
On rear axle, looks like I could shim either 3 degrees or four. I have 2 degree and 4 degree shims but would need to buy 3 degree if used.
Whew!.....
Any feedback or advice guys? Any recommendations on "inclinometer"?
Front to back....on my driveway which is not totally flat. Front of truck higher than back, but its all relative.
* Back of engine/transmission = 5 degrees downhill
* transfer case = 3.5 degrees downhill
* Rear axle pinion = 1.5 degrees positive tilted up towards T-case.
* Did not measure front axle yet.
These are average numbers. I used cell phone and harbor freight digital meter. Quite a bit of variability so I averaged.
Adjusting the transfer case will be easy as there is play from holes being slightly larger than bolts. I'll leave the top front bolts tight then use a jack to allow it to swing to desired angle before tightening.
On rear axle, looks like I could shim either 3 degrees or four. I have 2 degree and 4 degree shims but would need to buy 3 degree if used.
Whew!.....
Any feedback or advice guys? Any recommendations on "inclinometer"?