Cool air output
-
- Sweptline.ORG Member
- Posts: 3
- Joined: Wed Jan 26, 2022 11:06 am
- City: Lse
- State: AL
Cool air output
Hi back in this forum again on my d200 68 iv got a question reguarding the cool air intake on the left side under the dash i think theres missing something there its just a hole the heater box is on the right side but nothing on the left
-
- Sweptline.ORG Pioneer
- Posts: 7362
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Walnut Creek, CA
Re: Cool air output
That's normal. Unlike your post without periods at the end of sentences.Dodehedman wrote: ↑Wed Jan 26, 2022 11:38 pmHi back in this forum again on my d200 68 iv got a question reguarding the cool air intake on the left side under the dash i think theres missing something there its just a hole the heater box is on the right side but nothing on the left
Re: Cool air output
https://imageevent.com/jeffc/rust?p=2&n ... =4&s=0&z=2
this is the bracket that holds a plastic lid on the hole to keep the drafts out.
There should be a cable to open a close it marked as V on dash or kick panel on some trucks
this is the bracket that holds a plastic lid on the hole to keep the drafts out.
There should be a cable to open a close it marked as V on dash or kick panel on some trucks
Last edited by jeffc57 on Thu Jan 27, 2022 1:51 pm, edited 1 time in total.
Re: Cool air output
https://imageevent.com/jeffc/rust?p=2&n ... =4&s=0&z=2
this is the bracket that holds a plastic lid on the hole to keep the drafts out
this is the bracket that holds a plastic lid on the hole to keep the drafts out
- Wildergarten
- Sweptline.ORG Pioneer
- Posts: 1768
- Joined: Wed Mar 21, 2018 5:27 pm
- City: Los Gatos
- State: CA
- Contact:
Re: Cool air output
From your page:
This has been my intent. I have the screen 1/8 mesh stainless screen material, but I have not yet decided exactly how I am going to attach it to the cowel grille and cover. Glue? Brazed studs and nuts?
'69 W200 (thumbnail)
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
Re: Cool air output
cut large enough, trim to fit, to put the screws that hold the cowl though it, that way you can remove it if need to service service the wiper arms linkage, or glue to the back side of the cowl
-
- Sweptline.ORG Member
- Posts: 3
- Joined: Wed Jan 26, 2022 11:06 am
- City: Lse
- State: AL
Re: Cool air output
Ok thanks
-
- Sweptline.ORG Member
- Posts: 3
- Joined: Wed Jan 26, 2022 11:06 am
- City: Lse
- State: AL
Re: Cool air output
Thanks for your respons.then il make a box and houses and use the left one for cool air onley and control them whid wire from my new heat control unit