front core support all thread......question

juddoats · Post by **juddoats** » Sun Mar 20, 2011 3:33 pm

on my truck there is what seemed to have been fine thread on one end and course on the other end all thread of some sort that goes from core support to frame...there is a nut welded to the top side of the core support....is this stock or did someone do this after? with lowering mine so much i had to take out and put a longer piece in but i bought course threaded all thread since that was what was on the bottom so now i will have to take back and get fine and swap nuts on the bottom side of the frame....anyone know if this is stock?
thanks
Judd

crusty · Post by **crusty** » Mon Mar 21, 2011 4:12 am

That's how mine was. I don't see why you couldn't just use a bolt up from the bottom that is the correct thread pitch for the welded nut.

juddoats · Post by **juddoats** » Mon Mar 21, 2011 6:44 am

good idea i will try that...thanks

Post by **Hobcobble** » Mon Mar 21, 2011 7:19 am

juddoats wrote:on my truck there is what seemed to have been fine thread on one end and course on the other end all thread of some sort that goes from core support to frame...there is a nut welded to the top side of the core support....is this stock or did someone do this after? with lowering mine so much i had to take out and put a longer piece in but i bought course threaded all thread since that was what was on the bottom so now i will have to take back and get fine and swap nuts on the bottom side of the frame....anyone know if this is stock?
thanks
Judd

That is a stock piece.

John

MOPAT · Post by **MOPAT** » Mon Mar 21, 2011 9:29 am

You can buy those over the counter @ NAPA.
Fine on one end coarse on the other.

juddoats · Post by **juddoats** » Mon Mar 21, 2011 5:12 pm

do they come in different lengths? since i lowered my truck so much in the front i will need mine alittle longer

MOPAT · Post by **MOPAT** » Mon Mar 21, 2011 7:37 pm

Sure do.
I found the exact size no problem.

juddoats · Post by **juddoats** » Wed Mar 23, 2011 6:13 am

sweet thanks alot

juddoats · Post by **juddoats** » Tue Mar 29, 2011 1:11 pm

any idea what this is called that i should ask for a NAPA? i am ALWAYS referred to NAPA on this site but have yet to buy from them in Paris, TX maybe i have the worst NAPA store there is...because they never have or know what im talking about when i call them

powerwagoncrazy · Post by **powerwagoncrazy** » Thu Apr 07, 2011 12:04 am

You'll probably be looking for an exhaust manifold stud- I would envision a silence on the other end of the phone if you asked for a body mounting stud for a sweptline. Thread pitch on the welded nut is 7/16-20 UNF, other end is 7/16-14 UNC

juddoats · Post by **juddoats** » Thu Apr 07, 2011 6:12 am

i didnt say thats what i was looking for i told them it was fine thread on one end and course on the other....maybe that dosent ring bells with some but I would think it would if i worked in a auto parts store
thanks i will tell them that and see where i get
Judd

Sweptline.ORG

front core support all thread......question

front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question

Re: front core support all thread......question