Left my key in a different state. I need to hotwire my truck. I can get it to crank, but i believe i need to get it to the on position first. I think i'm missing a step.
Can someone jog my memory. See image below.
What pin to what pin to what pin.
Hotwire a Swepty
Hotwire a Swepty
Scott Blaylock (Founder/Admin)
http://www.Sweptline.ORG
http://www.SweptlineTruckRegistry.com
1965 Dodge SWB D100 (Utiline)
1968 Dodge LWB D100 (Sweptline)
1970 Dodge LWB D100 (Dude)
http://www.Sweptline.ORG
http://www.SweptlineTruckRegistry.com
1965 Dodge SWB D100 (Utiline)
1968 Dodge LWB D100 (Sweptline)
1970 Dodge LWB D100 (Dude)
Re: Hotwire a Swepty
Got it.
Wire between BAT to ING2 for power
Touch BAT to ST to start
Wire between BAT to ING2 for power
Touch BAT to ST to start
Scott Blaylock (Founder/Admin)
http://www.Sweptline.ORG
http://www.SweptlineTruckRegistry.com
1965 Dodge SWB D100 (Utiline)
1968 Dodge LWB D100 (Sweptline)
1970 Dodge LWB D100 (Dude)
http://www.Sweptline.ORG
http://www.SweptlineTruckRegistry.com
1965 Dodge SWB D100 (Utiline)
1968 Dodge LWB D100 (Sweptline)
1970 Dodge LWB D100 (Dude)
-
- Sweptline.ORG Pioneer
- Posts: 7362
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Walnut Creek, CA
Re: Hotwire a Swepty
Scott, I don't recall which one of the 2 IGN's is which, but one bypasses the ballast resistor for starting and the other is the "run" position. Both will work and "run", but if the ballast is bypassed for long, it will burn up the points.
-
- Sweptline.ORG Pioneer
- Posts: 4037
- Joined: Fri Feb 15, 2008 8:46 pm
- City: Wichita Falls
- State: TX
- Location: wichita falls,texas
Re: Hotwire a Swepty
I would run jumper from + terminal of battery to the ballast resister (correct side) . Use screwdriver across starter terminals to crank.
Bucky
Bucky
1966 W500
1975 W600
1978 W200 club cab
1975 W600
1978 W200 club cab
-
- Sweptline.ORG Member
- Posts: 419
- Joined: Wed Dec 31, 1969 6:00 pm
- City: Lawton
- State: OK
- Location: Lawton, Oklahoma
Re: Hotwire a Swepty
You can also run a jumper from the battery to the positive on the battery, then short across the starter relay. However this will throw your charging system into full charge mode so don't run it to long.
Life should NOT be a journey to the grave with the intention of arriving safely with a well preserved body, but rather to skid in sideways, beer in one hand,cigar in the other, body thoroughly used up, totally worn out and screaming,"what a ride"
-
- Sweptline.ORG Pioneer
- Posts: 7362
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Walnut Creek, CA
Re: Hotwire a Swepty
Check parts store for an ignition switch
Re: Hotwire a Swepty
I know I’m late but this did the trick.
Scott Blaylock (Founder/Admin)
http://www.Sweptline.ORG
http://www.SweptlineTruckRegistry.com
1965 Dodge SWB D100 (Utiline)
1968 Dodge LWB D100 (Sweptline)
1970 Dodge LWB D100 (Dude)
http://www.Sweptline.ORG
http://www.SweptlineTruckRegistry.com
1965 Dodge SWB D100 (Utiline)
1968 Dodge LWB D100 (Sweptline)
1970 Dodge LWB D100 (Dude)
- MrMopar
- Sweptline.ORG Member
- Posts: 373
- Joined: Thu Jun 09, 2011 11:41 am
- City: Lompoc
- State: CA
- Location: Lompoc, CA
- Contact:
Re: Hotwire a Swepty
Easiest way to do this, too easy.
Alan
Alan Erland
1967 Plymouth Barracuda
1969 Dodge Polara CHP
1969 Dodge Polara
1970 Dodge Camper Special
www.MrMopar.com
1967 Plymouth Barracuda
1969 Dodge Polara CHP
1969 Dodge Polara
1970 Dodge Camper Special
www.MrMopar.com