darty steering

Suspension, Brakes, Tires, Wheels steeringetc..
Post Reply
DUCKMAN

darty steering

Post by DUCKMAN »

Thanks alot you guys. You were right, my 4x4 converted '66 was way off on caster (it was set at about -10 degrees!). No wonder it was all over the road. The fix was to mount the solid spring pertch in the front and the 'live' shackle in the back by using one from a mid 80s ford ranger. This setup rotated the axle housing back enough to have a positive caster of 5 degrees and no driveshaft bind. Apparantly Sky Jacker lift springs concern themselves more with the lift than the axle orientation.
Now to correct for bump steer, do you reccommend a raised steering block to get the steering arm parallel or to go to a crossover steering link setup??

User avatar
wideblock
Founding Member
Founding Member
Posts: 5617
Joined: Wed Dec 31, 1969 6:00 pm
City: las cruces nm
State: NM
Location: Las Cruces, New Mexico
Contact:

Post by wideblock »

im no expert, but i would think the shorter the steering arm the stronger. so a raised steering block to put it all level would be best over the cross over. or, have you tryed a d400-600 steering arm? they are about 2-3 inches longer from the box to the end then the 1-200's arms are. might just solve your problem right there by dropping the steering arm rather then raising the axle link :Thumbsup
Trey

1965 CSS Utiline.


ex trucks:
70 D100
66 d100
66 d100
67 d100
69 d100
69 d200 crew cab
65 crew cab
66 d100
66 d100


"i don't know it all, but i know enough to be dangerous"

User avatar
RussRoth
Sweptline.ORG Pioneer
Sweptline.ORG Pioneer
Posts: 1345
Joined: Wed Dec 31, 1969 6:00 pm
City: Vancouver, WA
Location: Vancouver, WA
Contact:

Post by RussRoth »

Glad you got that fixed. Might be a little unfair to blame Highjacker since I think you have a later axle? Would be pretty hard for them to know exactly what the rig would require without some input from the owner.

I am sure Trey is right about the shorter arm being stronger and the bigger D steering arm might be a good bet. They may not work though since the cross shaft is likely much larger on the bigger rigs and would not fit yours. Crossover steering seems the route most guys go to eliminate bump steer. If you do have a later open knuckle front axle you can probably find a kit to make it crossover through one of the 4x shops.
RR
Vancouver, WA

'67 W200/450 CID
AA OD/SM465/205
PTO winch
4.10 powerlock
8R19.5 tires

User avatar
wideblock
Founding Member
Founding Member
Posts: 5617
Joined: Wed Dec 31, 1969 6:00 pm
City: las cruces nm
State: NM
Location: Las Cruces, New Mexico
Contact:

Post by wideblock »

i think they are the same steering boxs on all of them, so the arm should be the same in all but length :Thumbsup my service manual shows the same box specs for d100-600 on saginaws.
Trey

1965 CSS Utiline.


ex trucks:
70 D100
66 d100
66 d100
67 d100
69 d100
69 d200 crew cab
65 crew cab
66 d100
66 d100


"i don't know it all, but i know enough to be dangerous"

User avatar
Butch Romig
Sweptline.ORG Member
Sweptline.ORG Member
Posts: 332
Joined: Wed Dec 31, 1969 6:00 pm
City: garnett ks
Location: garnett kansas

Post by Butch Romig »

in case anyone is interested
i have steering gear,pittman arm,and drag link from a 69 W300 ,all the parts are larger than a 100-200 series ,id sell themas a unit
butch

Post Reply