A833 installation/adapting
-
- Sweptline.ORG Member
- Posts: 33
- Joined: Wed Aug 25, 2021 4:49 pm
- City: Jacksonville
- State: AL
A833 installation/adapting
I have a ‘68 D100 shorty, 225 3 speed. V8 bellhousing. I have an A833 4 Speed (actually I have 3) that I want to install. Anyone that’s tried this before knows tranny will not mate up to the bellhousing. My question is, has anybody come up with a way to adapt this? I’m locating a CNC shop to perhaps make a plate out of 1/4” steel, but I would prefer something a bit more cost effective. The trans came out of a ‘70 Hemi Challenger. I know I need a 23 spline disc and appropriate throw out bearing.
Last edited by DraytonCalhoun on Sat May 07, 2022 4:37 pm, edited 1 time in total.
-
- Sweptline.ORG Member
- Posts: 33
- Joined: Wed Aug 25, 2021 4:49 pm
- City: Jacksonville
- State: AL
Re: A833 installation/adapting
Just starting in on the resto/customization
- dodgeboykim
- Sweptline.ORG Pioneer
- Posts: 3016
- Joined: Wed Dec 31, 1969 6:00 pm
- City: Chilliwack. B.C. Canada
- State: Foreign
- Location: chilliwack.
Re: A833 installation/adapting
The way my buddy did his 66 D100 was to change to a later mechanical bell housing/Flywheel and clutch assembly with the hydraulic slave adapted on a custom bracket to work. The hydraulic bellhousing and related trans etc were tossed.
My truck is younger than me.
66 W100. 70 D 500 , 69 Hiab Speed Loader. 96 Ram 3500 Club Cab Cummin's 5 spd. 97 Ram 1500 Club Cab 5.9 gas auto. 83 W200 LB Propane 360 auto 09 Yammy Rhino 700.
66 W100. 70 D 500 , 69 Hiab Speed Loader. 96 Ram 3500 Club Cab Cummin's 5 spd. 97 Ram 1500 Club Cab 5.9 gas auto. 83 W200 LB Propane 360 auto 09 Yammy Rhino 700.
Re: A833 installation/adapting
"The trans came out of a ‘70 Hemi Challenger."
Can you post the partial VIN on it please?
Can you post the partial VIN on it please?
-
- Sweptline.ORG Member
- Posts: 33
- Joined: Wed Aug 25, 2021 4:49 pm
- City: Jacksonville
- State: AL
Re: A833 installation/adapting
I should have written it ‘supposedly’ came out of a Hemi Challenger. According to the guy I got it from many years ago.
Re: A833 installation/adapting
If it has a 0B VIN prefix, I can check it for you.
-
- Sweptline.ORG Member
- Posts: 448
- Joined: Fri Jan 01, 2021 11:46 pm
- City: Binghamton
- State: NY
Re: A833 installation/adapting
I do believe it would be an 18 spline if it was original from behind a hemi.DraytonCalhoun wrote: ↑Sun May 08, 2022 3:38 pmI should have written it ‘supposedly’ came out of a Hemi Challenger. According to the guy I got it from many years ago.
Late 65 w 200.
Factory LU-2 winch.
Updates: 205 transfer case,4.10 gears, disc brake Dana 60 front with lock out hubs
440 repower in the works
60 d100
383 with 727
4 wheel disc
3.73 geared rear
Factory LU-2 winch.
Updates: 205 transfer case,4.10 gears, disc brake Dana 60 front with lock out hubs
440 repower in the works
60 d100
383 with 727
4 wheel disc
3.73 geared rear
-
- Sweptline.ORG Member
- Posts: 33
- Joined: Wed Aug 25, 2021 4:49 pm
- City: Jacksonville
- State: AL
Re: A833 installation/adapting
Okay, cool. I had no idea.