426 Wedge install
426 Wedge install
I want to install a 426 Wedge motor in my 65. Does anyone know if the big cast iron ram horn exhaust manifolds that go up and back down used in Wedge cars from 62-64 clear on drivers side? Has anyone seen this done? Thanks!
-
pwadventurer
- Sweptline.ORG Member
- Posts: 353
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Saylorsburg, Pa.
Re: 426 Wedge install
Wow those are some crazy looking exhaust manifolds!
-
Wildergarten
- Sweptline.ORG Pioneer
- Posts: 1773
- Joined: Wed Mar 21, 2018 5:27 pm
- City: Los Gatos
- State: CA
- Contact:
Re: 426 Wedge install
Hopefully he can find a way to steer clear of them.
'69 W200 (thumbnail)
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
Re: 426 Wedge install
Is there an issue with them?
-
Wildergarten
- Sweptline.ORG Pioneer
- Posts: 1773
- Joined: Wed Mar 21, 2018 5:27 pm
- City: Los Gatos
- State: CA
- Contact:
Re: 426 Wedge install
By "steer clear" I meant that the steering tube and shaft would clear the manifold. One of those opportunities I couldn't pass up.
'69 W200 (thumbnail)
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
Re: 426 Wedge install
I am not that far in project. Will have to wait till I get motor in and try the exhaust just wondering if anyone else had used a set of theses manifolds in truck before. Yeah I'm worried they will hit steering. Really want to use them. Too cool not too!
-
Wildergarten
- Sweptline.ORG Pioneer
- Posts: 1773
- Joined: Wed Mar 21, 2018 5:27 pm
- City: Los Gatos
- State: CA
- Contact:
Re: 426 Wedge install
That was understood and agreed. I just can't pass up the opportunity for an exercise in pathetic license.
'69 W200 (thumbnail)
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
'68 W200 (RIP)
'68 W200 383 NP435 3.53
'67 W200 383 NP435 4.10 w overload springs, Dana 60, PTO winch & flatbed dump, racks, crane, c-air (Max)
Mark Vande Pol
Wildergarten.org
-
pwadventurer
- Sweptline.ORG Member
- Posts: 353
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Saylorsburg, Pa.
Re: 426 Wedge install
I saw this on FB from Josh. Looks like the master cylinder had to be relocated.