Rear end gearing

Engine, transmission, rear-end, driveline, fuel system etc..
Post Reply
fireguyfire
Sweptline.ORG Member
Sweptline.ORG Member
Posts: 268
Joined: Mon Aug 17, 2009 9:46 pm
City: Cochrane
State: Foreign
Location: Western Canada

Rear end gearing

Post by fireguyfire »

I am starting into the restoration of my 1970 D100. This truck has the 4 speed manual transmission and a 225" slant six engine. The truck moves along pretty well, but it has pretty low "farmer" gears in the diff; I'm not sure what the gear ratio is but will look for a tag once I get the rear end out of the truck.
My question is, how easy and expensive is it to change out the gear ratio in the rear end of one of these trucks? Is there a supplier out there of rear end gears?

earlymopar
Sweptline.ORG Member
Sweptline.ORG Member
Posts: 335
Joined: Thu Sep 22, 2011 11:37 am
City: Newberg
State: OR

Re: Rear end gearing

Post by earlymopar »

Changing out the original "3rd" member" or center section gear carrier in an 8-3/4 rear end is simple. Then you can simply reinstall everything with a 3rd member from another car or truck with the ratio you want. Buying a gear set (ring and pinion) and then replacing your existing gears is also able to be done but is a little more involved for someone who doesn't have the tools and experience to complete the job. Changing the gears is not difficult but setting them up correctly takes some time and the correct tools.

- EM

PwrWgnDrvr
Sweptline.ORG Pioneer
Sweptline.ORG Pioneer
Posts: 7339
Joined: Wed Dec 31, 1969 6:00 pm
Location: Walnut Creek, CA

Re: Rear end gearing

Post by PwrWgnDrvr »

The ratio is printed on the vin tag.

fireguyfire
Sweptline.ORG Member
Sweptline.ORG Member
Posts: 268
Joined: Mon Aug 17, 2009 9:46 pm
City: Cochrane
State: Foreign
Location: Western Canada

Re: Rear end gearing

Post by fireguyfire »

Cool; I'll check it out tonight.

User avatar
Hobcobble
Forum Moderator
Forum Moderator
Posts: 14573
Joined: Wed Dec 31, 1969 6:00 pm
Location: Lockport, NY

Re: Rear end gearing

Post by Hobcobble »

Probably the 3.91 Farmer ratio. :study :joker

John

fireguyfire
Sweptline.ORG Member
Sweptline.ORG Member
Posts: 268
Joined: Mon Aug 17, 2009 9:46 pm
City: Cochrane
State: Foreign
Location: Western Canada

Re: Rear end gearing

Post by fireguyfire »

Finally got around to looking at my vin tag; I have the 3.55 to 1 gears with heavy duty rear springs.
Does anyone have an opinion if this is a decent all around ratio? Havent driven the truck much before I tore it apart for a restoration.
If it would be improved by changing the gears, what ratio would you guys recommend for all around driving with quite a bit of highway driving mixed in?

712edf
Sweptline.ORG Pioneer
Sweptline.ORG Pioneer
Posts: 4019
Joined: Fri Feb 15, 2008 8:46 pm
City: Wichita Falls
State: TX
Location: wichita falls,texas

Re: Rear end gearing

Post by 712edf »

fireguyfire wrote:Finally got around to looking at my vin tag; I have the 3.55 to 1 gears with heavy duty rear springs.
Does anyone have an opinion if this is a decent all around ratio?
As far as passenger cars & 1/2 ton trucks, if there was ONLY one ratio available then I suspect this would be the best. I had 3.55 in my RR & GTX's, loved it.

With your 435 & the torque of the /6, acceleration shouldn't be an issue unless your tires are extremely tall/wide/heavy.
Hwy cruising however would benefit from taller tires.

Bucky
1966 W500
1975 W600
1978 W200 club cab

fireguyfire
Sweptline.ORG Member
Sweptline.ORG Member
Posts: 268
Joined: Mon Aug 17, 2009 9:46 pm
City: Cochrane
State: Foreign
Location: Western Canada

Re: Rear end gearing

Post by fireguyfire »

Thanks Bucky!

User avatar
Hobcobble
Forum Moderator
Forum Moderator
Posts: 14573
Joined: Wed Dec 31, 1969 6:00 pm
Location: Lockport, NY

Re: Rear end gearing

Post by Hobcobble »

The 3.55 is a nice gear as Bucky pointed out. The 3.23 is pretty decent too
if you weren't planning on doing a lot of heavy hauling or towing. :2cents :idea
John

Post Reply