odd ball question
odd ball question
im looking at this truck and was wondering if any of you guys know if a 65 shortbed utline with pto winch?
- soopernaut
- Sweptline.ORG Pioneer
- Posts: 8929
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Des Moines,IA
Re: odd ball question
It is an oddball question because, you either need to add a word or change a word before it could be answered.
Re: odd ball question
i meant to say is Know of. sorry i have had a long week.
Re: odd ball question
A '65 short wheelbase Utiline would be a W100. It has theSeff wrote:i meant to say is Know of. sorry i have had a long week.
Dana 44 & 60 eight lug axles and a 114" wheelbase. As
far as a PTO/Winch.... .... if these were added
back "in the day"..... they could be the Braden FTD7 PTO
that works off of the t-case and the Braden LU-2 winch.
John
Re: odd ball question
okay thank you ^^
Re: odd ball question
i got an email back about the truck. the seller said it is a project truck. last he worked on it he did a cab swap, swapped the 65 to a 67.the 65 was full of rust. the history of the truck is his dad bought it when he was 15 for a learning/beginner truck. does this sound like a project to get cheap?
Re: odd ball question
Sounds like a project or parts truck. If the PTO, winch and theSeff wrote:i got an email back about the truck. the seller said it is a project truck. last he worked on it he did a cab swap, swapped the 65 to a 67.the 65 was full of rust. the history of the truck is his dad bought it when he was 15 for a learning/beginner truck. does this sound like a project to get cheap?
shafts/pillow blocks are all there, they're worth a few bucks.
Post up some pics if you can.
John
Re: odd ball question
okay i will call the guy tmrw, im thinking about getting it cuz i want a powerwagon, what should i offer him, he wants 800 obo.
-
- Sweptline.ORG Pioneer
- Posts: 4019
- Joined: Fri Feb 15, 2008 8:46 pm
- City: Wichita Falls
- State: TX
- Location: wichita falls,texas
Re: odd ball question
You can get whole complete running PW's for not much than that. Sounds like the winch is the only thing worth while in this deal, assuming it is COMPLETE/WORKING.
In other words if much of the truck is missing or its disassembled then the amount (money & headache)to finish it may not be a good deal in the long run. What would it take to make it a runner?
Bucky
In other words if much of the truck is missing or its disassembled then the amount (money & headache)to finish it may not be a good deal in the long run. What would it take to make it a runner?
Bucky
Re: odd ball question
Post up some pics of the truck. If the truck isn't tooSeff wrote:okay i will call the guy tmrw, im thinking about getting it cuz i want a powerwagon, what should i offer him, he wants 800 obo.
rusted and if the engine/drive line isn't completely
whipped.... $800-ish isn't too bad. Perhaps he'd
take less if you're waving money in front of him.
John
Re: odd ball question
got an update on the 65. the guy sent me these photos. i know you guys are good judging if it would be worth it or not, so ill let you decide on it.
- Attachments
-
- 65PW3.jpg (30.49 KiB) Viewed 773 times
-
- 65PW2.jpg (39.01 KiB) Viewed 773 times
-
- 65PW1.jpg (36.21 KiB) Viewed 773 times
- surfnuke9
- Sweptline.ORG Pioneer
- Posts: 1119
- Joined: Fri Sep 12, 2008 9:51 am
- City: Churchton
- State: MD
- Location: Churchton, MD
Re: odd ball question
I wouldnt part with $800 for that truck. Too much missing, etc....
-
- Sweptline.ORG Pioneer
- Posts: 4019
- Joined: Fri Feb 15, 2008 8:46 pm
- City: Wichita Falls
- State: TX
- Location: wichita falls,texas
Re: odd ball question
Ditto.... even if you needed ALL the parts off of it for another truck, $800 is pushing it.surfnuke9 wrote:I wouldnt part with $800 for that truck. Too much missing, etc....
As for finishing the truck itself, too much missing.
Bucky
Re: odd ball question
well i have a 65 d100 that i can use for parts. im just wondering what i should offer the guy, he says the utiline bed he has is good, but i emailed him asking for a photo of it. any idea on how much that winch is worth?
-
- Sweptline.ORG Pioneer
- Posts: 4019
- Joined: Fri Feb 15, 2008 8:46 pm
- City: Wichita Falls
- State: TX
- Location: wichita falls,texas
Re: odd ball question
I'd say if the winch is complete & in working order then $350-$400
Bucky
Bucky
- soopernaut
- Sweptline.ORG Pioneer
- Posts: 8929
- Joined: Wed Dec 31, 1969 6:00 pm
- Location: Des Moines,IA
Re: odd ball question
Between the axles and the winch you probably have $800 in parts plus whatever you can get for the rest.
Re: odd ball question
If the PTO, shafts/pillow blocks & winch
[with actuator cable & hand throttle]
are all there, I'd say its worth $500-$600
all day long. I don't think you'd tick
this guy off if you offered $550 for
truck as it sits.
John
[with actuator cable & hand throttle]
are all there, I'd say its worth $500-$600
all day long. I don't think you'd tick
this guy off if you offered $550 for
truck as it sits.
John