Another request, I think this is a really hard item but I and looking for the plastic rectangle pieces with the ears that clip and hold your lower body trim pieces. If you have a source that would much appreciated.
Thank you.
Rick out
Plastic Body Moulding Trim Clips
- rmansberger
- Sweptline.ORG Member
- Posts: 101
- Joined: Wed Oct 02, 2013 2:44 pm
- City: East Lansing
- State: MI
- Location: East Lansing, MI
- Contact:
Plastic Body Moulding Trim Clips
Rick Mansberger
1967 Mustang "Duke"
1970 Dodge D100 "The Dude"
1978 GMC Suburban "Big Cub"
2006 C300
2014 RAM Limited "Master Sergeant"
517.599.7667
1967 Mustang "Duke"
1970 Dodge D100 "The Dude"
1978 GMC Suburban "Big Cub"
2006 C300
2014 RAM Limited "Master Sergeant"
517.599.7667
Re: Plastic Body Moulding Trim Clips
Try this place: http://www.restorationspecialties.com/Catalog-PDF.html
1970 W200
318, NP 445
Factory LU-2 winch
A/C, HD Gauges
318, NP 445
Factory LU-2 winch
A/C, HD Gauges
Re: Plastic Body Moulding Trim Clips
If you mean the small square ones that screws go into they are available in the generic(IE Dorman) parts section at a parts store.
- CMR70D3
- Sweptline.ORG Member
- Posts: 238
- Joined: Fri Mar 05, 2010 10:02 pm
- City: Martinsville
- State: IN
- Location: Southwest of Indy
Re: Plastic Body Moulding Trim Clips
Try this link,hope their still in business. viewtopic.php?f=30&t=34630
71' D100 "Custom 100" LWB, 383 BB,AT,PS,PB,AC,BUCKET SEATS
Chris
Chris
- rmansberger
- Sweptline.ORG Member
- Posts: 101
- Joined: Wed Oct 02, 2013 2:44 pm
- City: East Lansing
- State: MI
- Location: East Lansing, MI
- Contact:
Re: Plastic Body Moulding Trim Clips
Thanks Chris, Tonkin is still and business and had the part for 93 cents each compared to Mopar sources at $5.95 per clip.
Rick out
Rick out
Rick Mansberger
1967 Mustang "Duke"
1970 Dodge D100 "The Dude"
1978 GMC Suburban "Big Cub"
2006 C300
2014 RAM Limited "Master Sergeant"
517.599.7667
1967 Mustang "Duke"
1970 Dodge D100 "The Dude"
1978 GMC Suburban "Big Cub"
2006 C300
2014 RAM Limited "Master Sergeant"
517.599.7667
- CMR70D3
- Sweptline.ORG Member
- Posts: 238
- Joined: Fri Mar 05, 2010 10:02 pm
- City: Martinsville
- State: IN
- Location: Southwest of Indy
Re: Plastic Body Moulding Trim Clips
Good deal!
71' D100 "Custom 100" LWB, 383 BB,AT,PS,PB,AC,BUCKET SEATS
Chris
Chris
- rmansberger
- Sweptline.ORG Member
- Posts: 101
- Joined: Wed Oct 02, 2013 2:44 pm
- City: East Lansing
- State: MI
- Location: East Lansing, MI
- Contact:
Re: Plastic Body Moulding Trim Clips
Tonklin is no longer a source for the body trim moldings, they only had 11 left and are now discontinued. I got the last 11.
If anyone has another source, please let me know.
Rick out
If anyone has another source, please let me know.
Rick out
Rick Mansberger
1967 Mustang "Duke"
1970 Dodge D100 "The Dude"
1978 GMC Suburban "Big Cub"
2006 C300
2014 RAM Limited "Master Sergeant"
517.599.7667
1967 Mustang "Duke"
1970 Dodge D100 "The Dude"
1978 GMC Suburban "Big Cub"
2006 C300
2014 RAM Limited "Master Sergeant"
517.599.7667
- martincom
- Sweptline.ORG Member
- Posts: 448
- Joined: Thu Jul 30, 2020 10:04 am
- City: Five Points
- State: AL
Re: Plastic Body Moulding Trim Clips
New source for sweptline plastic moulding clips: www.mrgusa.com
Lower Rocker Panel Molding (wide): FA413
This is a GM clip that requires trimming off the raised side shoulders. It is the same clip that was previously supplied by Tonklin.
Front fender sweptline moulding clips: FA4804
This is an exact duplicate of the clip and is the type that snaps into a fender hole and secured by a drive-in pin. These are are some pretty old clips. The first three I attempted to install shattered when driving in the pin. I had to warm them up with the heat gun, to make them somewhat pliable, before installing.
Lower Rocker Panel Molding (wide): FA413
This is a GM clip that requires trimming off the raised side shoulders. It is the same clip that was previously supplied by Tonklin.
Front fender sweptline moulding clips: FA4804
This is an exact duplicate of the clip and is the type that snaps into a fender hole and secured by a drive-in pin. These are are some pretty old clips. The first three I attempted to install shattered when driving in the pin. I had to warm them up with the heat gun, to make them somewhat pliable, before installing.
1*1971 D100 318 A/T
1*1970 Charger R/T 440-6PK A/T
2*1969 Daytona Charger 440 A/T
1*1969 Coronet R/T awaiting restoration
1*1969 Torino Talladega awaiting restoration
1*1970 Charger R/T 440-6PK A/T
2*1969 Daytona Charger 440 A/T
1*1969 Coronet R/T awaiting restoration
1*1969 Torino Talladega awaiting restoration