Sweptline.ORG

Have you tried jumping starter relay to see if it turns over. Ballast has nothing to do with engine not turning over.
If it turns over then check at switch and wiring to relay.

PTO off the 435 trans. Crane is a 1969 Hiab Speedloader. I am no PTO geek. On the truck I am building I have a dual output Braden PTO (output shaft comes out both front and rear) mounted on my NP201. The plan is to run both the winch and the hydraulic pump that runs the dump bed with the same PTO, ...

DaltonSparks wrote: ↑

Sat Apr 06, 2024 7:28 pm

Dodgeboykim that's a sweet truck, is that crane powered by the pto? Or is it electric over hydraulic?

PTO off the 435 trans. Crane is a 1969 Hiab Speedloader.

This is my 70 D500 toy. Pulled 318-3 and installed a 400 BB i had in shed.

Truck had 25000 original miles but sat in a barn for 25 or so years before I got it in 2002.. Engine was seized,

Once I either find a part number or get some made I'll post it here. Now the wheel cylinder PT# was a dorman W28661. I paid $65+ a piece but they were a exact match Definitely different wheel cylinders than the ones in my 70 D500. My truck has 2 wheel cylinders per wheel. Front and rear axle in min...

When I worked on the brakes for my D 500 I needed some small parts for adjusters. Ordered them at a medium/heavy duty truck part6s supplier.

As you said, Other manufacturers used the brakes/axles.

I have a 70 D500 and did brakes a number of years ago. Not sure what push pin you are referring too,
Got a pic of it.

So I am considering painting the roof on my 65 power wagon. It’s a red truck, the wagon wheels are white and the bumpers are flat black. Questions are, do I go with black on the roof or white. Did dodge ever paint roofs white or black when the truck had small back window, and if so how much of it g...

So I am considering painting the roof on my 65 power wagon. It’s a red truck, the wagon wheels are white and the bumpers are flat black. Questions are, do I go with black on the roof or white. Did dodge ever paint roofs white or black when the truck had small back window, and if so how much of it g...

Should be able to source boots at Auto parts suppliers. Lordco, Napa, Even Amazon shows them.

I would like to give dodgeboykim (Kim) a formal big Thank you for the pictures of the hood placement for the Powerwagon emblems. 2 thumbs up, and hopefully i can help you in the future. Steve Thanks and Your Welcome. Truck those picture's were from was sold a couple years back as a parts truck. Goo...

Hello all, My question is regarding a front end swap. I have an opportunity to pickup a 65 front core support and grill assembly to change out a 69 front. I don't have a early hood just a 68 straight bottom lip one. Will the 65. Grill wings interfere with the hood bottom lip? Also how funky is a bi...

Have you looked at any Mopar Restoration Parts suppliers. Lots of common little parts were used for both cars and trucks.

Search power steering etc in group. A long post regarding it.

I have pictures with those measurements taken on a hood. Message me e mail addy and I will send them to you.

The only 5 lug Budd that I am aware of are the D400 trucks & M400 motor homes. I could see the motor homes having front disc brakes. It being 5 lug probably means those specs I gave in my original post may be invalid. Square tube rear axle is Rockwell. Standard fare in medium dutys. Bucky I agree. ...

I have a 70 D500 and found all my brake parts at a Medium/Heavy Duty truck parts supplier. Dodge was not the only one to use those brake systems.

Search power steering in group. Lots of threads. Also search this part of group.

viewforum.php?f=20&start=50

I came at this from a slightly different angle This starter carries the same Chrysler p/n as the 2 bolt starter used in industrial big block applications. It is used in slant six fork lift applications If the picture is accurate it is a 2 bolt starter with a mounting configuration very similar to t...

I pulled apart a 70 wiper motor and put it back together the wrong way. Had to fiddle with it to reclock to correct position.