Sweptline.ORG

? did you get the brakets with the engine? in the late 70,s and 80,s the belts were run up around a couple of idler pullies that were apr in the area of the thremosat to run the Ac /water pump thats why it doesn,t line up with the fan the fan was driven off the crank then to the power steering- to m...

11s in the1/4 in a 2 ton truck will be real Trick if You can pull it off :salut :salut have a 1970 Adventurer 318 auto 3.55 stock did1/4 17.01 sec engine blew rebuilt it with Speed Pro 9-1 pistons flat tops moly rings Hasting bearings Windage tray valley tray .441 lift int exh deg at 112 ported head...

LC from PA you didn,t say what size engine you had but if it is a 318 you may have a low volume low psi pump I had the same type trouble with vapor lock go to NAPA and get a pump for a 360 more PSI and Volume fixed me up LC

LC from PA I have a 71 D100 that was order new by the owner with the 16" wheels and 10 ply tires so he haul heavy and still title it as a 1/2ton I have all 4 wheels I live in PA close to Johnstown about 20 miles off the Somerset exit of the Pa turnpike if you every come this way PM me and will make ...

LC from PA working on a 1976 Dodge Custom 100 Warlock 360 727 9 1/4 rear end I also have a 1971 D-100 6cyl manual 3 spd 8 3/4 rear end 3.91 Posi ? is can I just unbolt the U bolt Brakelines ETC and just swap rear end ? can,t find any perch measurements in my manuals Has any one try this or got input...

LC from PA want to Thank You for being a shop teacher :study :study :study I was a young motor head in 1970 when our local Vo-Tech high school opened and I enrolled in the auto repair for 11th,12th grade had a exp. mech as a teacher he showed how to to do things right the 1st time by reading the man...

LC from PA my weather stripping has been on for apr 14 years still sealing no water leaks some air noise at 100 just take your time dry run the fit before gluing should have about 1-2" extra in center of bottom of door LC

LC from PA when looking for hubcaps dogdish or full size they are Stainless Stell

LC from PA the problem with the door seal is the upper edge at vent is narrow so the round weather stripping won,t compress I had this problem on my 70 I cut the outter edge off and just left the glued on part that runs down the vent window runangle then I went to Restorastion Specialites which is i...

LC from PA I took a bedliner from a late 70 long bed that had the rails over the top edge of the bed did a little measuring to cut off to just fit under lip I left the front bed lip on only problem was the wheel weel shape was just a little off had to jump on it to pop it down in it will never blow ...

LC from PA wish my transplant of a 3on the tree to the floor looked so nice :salut :salut I had to do mine because the shifter broke off in my hand with a load on going down hill :pale :pale :pale made the Sparkamatic kit work but to get Rev and 2nd had to take out Ashtray to get into gear :lol: :lo...

LC from PA I have a 1971 D-100 Slant 6 factory power brakes if you need any info PM and I will check my truck to see how things are hooked up IT Brakes Alot better than manual LC

LC from PA I have a 70 Adventurer in 2000 I couldn,t find clips if you go to take the panel off start at the bottom get it all loose then gentley push up the top has 2 small finger tabs that if you twist to much they will break they are held onto tailgate by a slot that goes over a pin on the gate S...

LC from PA do you need a gas tank ? or just the measurement for mounting tank? I have a tank from a Std cab that I can give you sizes high ,long,deep so you could see if it will fit in cab send PM and I will check it for You LC

Hi Jimmy LC from PA Looks Good from the East Coast where did you find the chrome Pas side mirror braket? PM and let me know Thanks Looking Good

OK Guy,s LC from PA lets get this Right if We would have voted for the groundhog in Nov We would Know both the weather and how deep a Hole we are in and the Groundhog only lies 50% of the times lets send him to Washington LC

LC from PA 70,71 Adventurer,s had Pin Stripping at the Top Black or White was the color choice the Bright moulding goes back to 65or earlier LC

LC from PA the lens without holes are Early 70, lens that pushed in had small tabs on each end that broke off after being pulled out a few times to replace bulb the lens with holes fit but you need the longer mounting screws also the bases were changed some what were used till end of D-series was ch...

LC from Pa from a early post bulb # 330

LC from PA the on hood turn signal bulbs are held in place by the threaded collar that the wire goes up thru the inner threads are justed crimped to the mounting plate :shame :shame :shame DO NOT use a lot of turning force or you will break the crimp loose and you are in need of a Replacement this u...