Sweptline.ORG

Anyone here running one on a 440 or RB for that matter. I purchased one from a friend of a friend and it was only installed and removed. My issue is it talks in the instructions about a ground wire inside the distributer ? Where does it need to go to. The igniter 3 only has a black and red wire comi...

Guys Ive looked all over internet with not a bit of luck. I Complete parts list and Diagram for a A833 4 speed. Ive found the Diagram with all the part numbers but i cant find a complete list of what the part numbers are? like what the part is called. theres a large nut witha smaller nut on top of i...

Restoration specialties has them on page 212 of there online catalog.

I think it was probably me! I wasnt sure. I was going threw my pic folder and stumbled on it and i wasnt sure if i ever posted it or not. I've had it saved for close to two years i bet.

Im with you On this one Robin! Dont be a pretender. If its loud you better be able to back it up!

1964 Buick Sweptline! LOL ...kinda cool

I see! thanks

Moderators......why cant i use the search option in here? says Im not permitted??

I used the crossfire brand paint from Napa. Its Urethane enamel . From what i can remember i had a paint code that i found in a old PPG paint code book And they cross referenced the PPg # with the Crossfire brand paint and came up with this number.... 55A - 1417.... http://i43.tinypic.com/35bw5j9.jp...

Can someone here tell me the actual diameters of both smaller and larger guages in this pic. Im trying to figure the same setup using autometer guages but im not having enough room "if i use the four smaller ones OIl , Water , Fuel , Volt " to be able to use a tach and speedo in the center without t...

i swapped from a slant six to a 440 and the powersteering pump is from a rb bigblock car. I had to get lines made at a hydralic repair shop. Real hard to find a factory lines that work" has far has bends and fittings go!.. Getting lines made isnt a big deal and place that works on tractors ect can b...

you can also take out the defrost ducts and measure them also.

Robin you need to search craiglist. I found a few cherokee's today that where under $1000. One especially that was $400 and it would drive you home. If you have the room for a whole vehicle. You could part it out and break even for sure on the deal. these cherokee's have somewhat of a cult following...

the B should be the blower switch for the fan motor. And the V is for the cowl vents. There is one on the far left and on the far right up under the dash. One will be right above the e-brake handle and the other is in the same spot but on the other side.

are you talking about the heater control on a late body... like seventys and seventy-ones? s If you look at the pic i posted. You see the lowest panel that has the three heat controls in it. This panel is a seperate piece then the dash. It is spot welded on. This panel is what im talking about. I c...

thanks guys.
I havnt seen what im talking about yet.
More pics please!.........thanks...Cliff

Or info on the lower sections that are tack welded on. What im talking about are the dash sections that have the defrost/heat/blower switch controls mounted to. Now im not sure as to all the years im talking about but lets start with 1967. Which is the year i have and ill show you a pic of mine exac...

my pop has a 78 300d and those motors are soo overdesigned its almost funny! All caps are threaded aluminum o-ring sealed! Very well designed little motors. His plans were to drive it then eventually put the motor in a A100 truck. but the car is to nice to mess with right now. Its a California rust ...

MY God MAN! I wouldnt drive that ratsnest of a wiring mess you have there. to afraid to get burned up! lol For real i would go with this wiring kit like i just did! its super easy and it can be done with a buddys help in a weekend or two! So far ive only ran the wires to the rear lights and sending ...

Ive got a rather nicely made bench seat available to me that i would love to put in my truck. Thing is its 3 inches narrower then the stock bench. Im wondering how its going to center up with the steering wheel. Or would it look funny to have the seat more to the driver side to sit you in center of ...